Login

Privacy Policy (GDPR)
Authorization
Not registered yet? Take advantages of registration:
Products saving in a binding to the projects
Product consultation from our experts - Online
Registration
Signup
By using this form, you confirm that you have read the site terms of use Terms of use and completely accept the terms of use

VENTS KSA 150-2E (220/60)


Compact sound- and heat-insulated centrifugal fan with forward-curved impeller blades. Maximum capacity - 836 m3/h.

  • Description
  • Characteristics
  • Downloads
  • Dimensions
  • Additional diagrams
  • Designation key
Description
Description
APPLICATIONS
  • KSA fan design enables their application in supply and exhaust ventilation systems for the premises with high noise level requirements. 

  • Suitable for connection with Ø 100, 125, 150, 160 and 200 mm round ducts.
DESIGN
  • The fan casing is made of aluzinс. 
  • Heat- and sound-insulating layer is made of polystyrene foam.

MOTOR
  • The impeller with forward curved blades made of galvanized steel is powered by 2- or 4-pole external rotor asynchronous motor.

  • The motor is equipped with the ball bearings for long service life.

  • For precise features, safe operation and low noise, each impeller is dynamically balanced while assembly.

  • Motor protection rating IP44.

     

SPEED CONTROL
  • Smooth or step speed control with a thyristor or autotransformer speed controller.

  • Several fans may be connected to one speed controller provided that the total power and operating current do not exceed the rated speed controller parameters.
MOUNTING
  • Connection pipes have round section.

  • The fan basic delivery set includes a power cord without an electrical plug.

  • Electric connection and mounting shall be performed in compliance with the operation manual and wiring diagram.
THE FAN WITH ELECTRONIC TEMPERATURE AND CONTROL MODULE (U OPTION)
  • The ideal solution for ventilation of the premises requiring permanent temperature control, i.e. greenhouses. 

  • The fan with the electronic temperature and speed control module provides automatic control of the motor speed (air flow) depending on air temperature in the air duct or in the room.
  • The front panel of the electronic module has the following control knobs:
    • speed control knob for setting the motor speed;
    • thermostat control knob for setting the temperature set point;
    • thermostat indicator light.
  • The fan is available in two modifications:
    • with the temperature sensor integrated inside the fan air duct (U/U1/U2 option);
    • with the external temperature sensor fixed on the cable, 4 m long (Un/U1n/U2n).
Control logic of the fan with the electronic temperature and speed control module
  • Set the desired air temperature (thermostat set point) by turning the thermostat control knob. Set the required minimum impeller speed (air flow) by turning the speed control knob. The motor switches to maximum speed (maximum air flow) as the temperature reaches and exceeds the set temperature set point.

  • The motor switches to the pre-set lower speed as the temperature drops down below the temperature set point. To avoid frequent motor speed switches when the air temperature in the duct is equal to the set temperature point, the speed switch delay is activated.
There are three switch delay patterns for various cases:
  1. The temperature sensor-based switch delay (U option): the motor switches to higher speed as the air temperature exceeds 2 °C above the set thermostat set point. The motor revers to the preset lower speed as the air temperature drops below the thermostat set point. This pattern is used to keep air temperature to within 2 °C. In this case the motor speed switches are rare.
  2. The timer-based switch delay (U1 option): as the air temperature exceeds the set thermostat set point, the motor switches to higher speed and the switch delay timer is activated for 5 min. The motor reverts to lower speed as the air temperature drops down below the thermostat set point and only after 5 minuts timer countdown. This pattern is used for exact air temperature control. The speed switches for the fan with U1 option are more frequent as compared to the operating logic of the fan with U option, however the minimum operating cycle at one speed is 5 minutes.
  3. Switching ON/OFF by a temperature sensor (U2 option): when the air temperature exceeds by 2 °C the thermostat actuation set point, the fan starts operating at the set speed. The fan switches off when the temperature drops below the temperature set point.
VENTS KSA fan greenhouse ventilation example
Characteristics
Characteristics
Parameter KSA 150-2E (220/60)
Measurement unit
Engine Type 220V / 60Hz -
Phase 1 ˜
Voltage 230 V
Frequency 60 Hz
Sound pressure level at 3 m distance 66 dBА
Pressure 725 Pa
Power consumption 140 W
Maximum air capacity 836 m³/h
Maximum transported air temperature 25 +40 °С
Protection rating IP X4 -
Weight 6.28 kg
Spigot size 150 mm
Number of poles 2 -
Files archieve
Downloads
Select document type
  • Advertising and printing products
  • Certificates
  • Technical documentation
Name
"VENTS KSA" user's manual 06-2022 (V42EN-08) (pdf 1.53Mb)
"VENTS KSA" product description 09-2020 (pdf 1.15Mb)
Download high quality image "VENTS KSA" (psd 3.57Mb)
Certificate GS "KSA" (pdf 134.2Kb)
Declaration of сonformity "KSA,KSB" (pdf 1.67Mb)
Certificate LVD "KSA" (pdf 107.7Kb)
Download image "VENTS KSA" for your website (png 797.16Kb)
Dimensions
Characteristics
VENTS  KSA 150-2E (220/60)
Parameter Value Measurement unit
∅D 148 mm
B 231 mm
H 343 mm
Р 48 mm
L 358 mm
Additional diagrams
Additional diagrams


Designation key
Designation key
Series Spigot diameter Polarity Phase Options
VENTS KSA 100; 125; 150; 160; 200 2, 4 Е: single phase U: speed controller with an electronic thermostat and a temperature sensor integrated inside an air duct. Temperature-based operation logic.
Un: speed controller with an electronic thermostat and a temperature sensor fixed on a 4-meter cable. Temperature-based operation logic.
U1: speed controller with an electronic thermostat and a temperature sensor integrated inside an air duct. Timer-based operation logic.
U1n: speed controller with an electronic thermostat and a temperature sensor fixed on a 4-meter cable. Timer-based operation logic.
U2: speed controller with an electronic thermostat and a temperature sensor integrated inside an air duct. Temperature-based switching on/off.
U2n: speed controller with an electronic thermostat and a temperature sensor fixed on a 4-meter cable. Temperature-based switching on/off.
R1: power cord with a mains plug.
P: integrated smooth speed controller.
Share your opinion

Questionnaire
Where have you learned about us?