VENTS NKD 150-2,0-1 A21 V.2

Description
Characteristics
Capacity diagram
Downloads
Dimensions
Designation key
Compatibility table
Electric heater power selection diagram

Description

APPLICATION
The heater is designed for integration into a ventilation system and joint operation with an air handling unit equipped with a control system used to switch on the heater and control its operation.	The heater maintains the supply duct air temperature at a point set by the unit controller.
DESIGN
The casing, the junction box and the heater cover are made of galvanized steel with the heating elements in stainless steel. The heater casing is additionally heat-insulated with 20 mm non-flammable mineral wool layer. The heaters are equipped with rubber seals for airtight connection to the air ducts. NKD A21 V.2 duct heaters are equipped with a factory-wired power cable and a control cable, and also have a duct temperature sensor that is connected to the ventilation unit.	Temperature control is carried out smoothly by the ventilation unit controller due to the PWM signal in cycles of 10 seconds. Load commutation is carried out by the semiconductor device (triac). The heaters are equipped with overheat thermostats: ⏵main overheat protection with automatic reset at +50 °C ⏵emergency overheat protection with manual reset at +90 °C
MOUNTING
The heater design ensures its mounting on the round ducts in any position by means of clamps (included in delivery). The air flow direction shall match the direction of the arrow on the heater casing.	In case of horizontal mounting the control box must be installed with the cover upwards. Swivel range from the normal position up to max. 90°. Do not install the control box with the cover downwards.

Characteristics

Parameter	NKD 150-2,0-1 A21 V.2	Measurement unit
Minimum air capacity	170	m³/h
Current	8.7	A
Power	2000	W
Heating	electric reheating	-
Duct	for round air ducts	-
Connection diameter	150	mm

Capacity diagram

Selection method:
Air flow:
Pressure:

Operating point

Air flow: --
Pressure: ---

Files archieve

Downloads

Dimensions

Characteristics

Parameter	Value	Measurement unit
∅D	150	mm
B	189	mm
H	280	mm
L	306	mm
L1	192	mm

Designation key

Series	Connected air duct diameter [mm]	-	Heater power [kW]	-	Phases	Options
NKD	125; 150; 160; 200; 250; 315	-	0.6; 0.8; 1.2; 1.7; 2.0; 3.0	-	1: single-phase	A21 V.2: compatible with A21 automation, without a DB-9M connector

Compatibility table

Heater model (connected air duct diameter)
NKD 125 A21 V.2	VUT/VUE VB EC A21
NKD 150 A21 V.2	VUT/VUE VB EC A21
NKD 160 A21 V.2	VUT/VUE VB EC A21
NKD 200 A21 V.2	VUT/VUE VB EC A21
NKD 250 А21 V.2	VUT/VUE VB EC A21
NKD 315 A21 V.2	AirVents with a 315 mm spigot and an A21 automation without a DB-9M connector

Electric heater power selection diagram

The NKD A21 V.2 heater parameters calculation example:

It is necessary to select a heater for supply air post-heating to a temperature of +24 °C, provided the temperature downstream of the heat exchanger is +17 °C. Therefore, it is essential to increase temperature by 7 °C. The ventilation system incorporates the VUT 350 VB EC A21 air handling unit. The rated air flow is 400 m³/h. Determine the intersection of the post-heating temperature line (+7 °C) and the rated air flow line (400 m³/h).
In this case the 1200 W heater capacity provides necessary post-heating (+7 °C). The heater NKD 160-1,2-1 A21 V.2 with the diameter matching the spigot diameter of the VUT 350 VB EC A21 air handling unit is a suitable model.