NKV 125-4

Description
Characteristics
Downloads
Dimensions
Additional diagrams
Legend

Description

APPLICATIONS

Duct water heaters are designed for heating of supply air in round ventilation systems. They can be also applied in supply or supply and exhaust ventilating units.

DESIGN

The heater casing is made of galvanized steel, the tubular coils are of copper tubes and the heat exchange surface is made of aluminium plates. The heaters are equipped with rubber seals for airtight connection to the air ducts. The heaters are ailable in 2 and 4 rows modifications and are designed for maximum operating pressure 1.6 MPa (16 bar) and maximum water operating temperature +100°С. The outlet manifold has a branch pipe for installation of submersible temperature probe or icing protecting device. The heater is equipped with a nipple for the system deaeration.

MOUNTING

The heater design ensures its mounting on the round ducts in any position by means of clamps. The water heating coils can be installed in any position that enables the heater deaeration. The air flow direction shall match the pointer designation on the heater.

The mounting shall be performed in such a way as to enable the uniform air stream distribution along the whole cross section.

The air filter shall be installed at the heater inlet to protect the heating elements against pollution.

The heater can be installed at the fan inlet ot outlet. If the heater is located at the filter outlet the air duct between the heater and the filter shall have the length of at least two connecting diameters to ensure the air flow stabilization as well as permissible air temperature level inside the fan.

The heater shall be connected on the counterflow principle, otherwise its efficiency can drop by 5-15%. All the nomographic charts in the catalogue are valid for such connection.

If water serves as a heat medium the heaters are suitable for indoor installation only. For outdoor installation use antifreeze mixture, i.e. ethylene glycol solution.

To ensure the correct and safe heater operation use the automation system that provides complex control and freezing protection:

automatic control of heating elements capacity and air heating temperature;
switching ventilating system on after preliminary heating with the heater;
use of air curtains equipped with spring-loaded actuator;
filter checking by means of differential pressure sensor;
fan shutdown in case of the heater freezing danger.


Connection against air flow	Connection along air flow

Air pressure loss for water heaters

NKV round series

Characteristics

Parameter	NKV 125-4	Measurement unit
Weight	5.3	kg
Number of water coil rows	4	-
Round duct size	125	mm
Heating	water heating	-
Duct	for round air ducts	-
Connection diameter	125	mm

Files archieve

Downloads

Dimensions

Characteristics

Parameter	Value	Measurement unit
∅D	124	mm
B	350	mm
H	230	mm
H3	150	mm
L	300	mm
L1	28	mm
L2	65	mm
L3	220	mm
K	G 3/4''	mm

Additional diagrams

How to use water heater diagrams:

Air Speed. Starting from 250 m³/h on the air flow scale draw a vertical line ¹till the air speed axis which makes about 3.75 m/s.

Supply air temperature. Prolong the line ¹up to the point where it crosses the outside air temperature (blue curve), e.g. -15°C; then draw a horizontal line ²from this point to the left till crossing water in/out temperature curve (80/60 °C). From this point draw a vertical line ³to the supply air temperature axis on top of the graphic (+27°С).
Heating coil capacity. Prolong the line ¹up to the point where it crosses the outside air temperature indicated as red curve (e.g., -15°С) and draw a horizontal line ⁴from this point to the right to the intersection of water in/out temperature curve (e.g., 80/60 °С). From this point draw a vertical line ⁵up to the scale of heating coil capacity (5.2 kW).
Water flow. Prolong the line ⁶down to water flow axis at the bottom of the graphic (0.067 l/s).
Water pressure drop. Draw the line ⁷from the point where line ⁶crosses the black curve to the pressure drop axis. (5.2 kPa).

Legend

Series		Flange diameter [mm]		Number of water coil rows
NKV		100; 125; 150; 160; 200; 250; 315		2;4

VENTS NKV 125-4