VENTS PA 02 W4

Print version Save in PDF format

Suspended air supply unit with the air flow up to 2350 m³/h in the sound- and heat-insulated casing with the water heater

Add to project

Add to compare

Description
Characteristics
Capacity diagram
Downloads
Dimensions
Additional characteristics
Hot water coil parameters
Designation key
Accessories

Description

DESCRIPTION	CASING
The PA unit is a ready to use ventilation unit for air filtration, warming and supply to the room.	Steel casing covered with aluzinc coating internally filled with 50 mm heat- and sound-insulating layer made of mineral wool.
FILTER	HEATER
Integrated panel G4 filter ensures sufficient supply air purification (optionally F7).	The PA units are equipped with water heater. Depending on the required heating capacity the water heaters are available in two-, three- or four-row modifications. The water heaters are designed for max. operating pressure 1.0 MPa (10 bar) and max. operating temperature 95 °C of the heat medium.
FAN
The unit is equipped with a direct-driven centrifugal fan with backward curved blades and external rotor motor. The fan configuration ensures the best operating characteristics: high air flow and efficiency combined with low noise level.
MOUNTING
The unit is designed for indoor installation either on the floor, on the wall or under the ceiling by means of a seat angle with inserted vibration-damping element or attached to a wall with brackets. The unit can be mounted either in service spaces or in main premises above the suspended ceiling, in the pocket or the unit can be placed directly in the room. All the electrical connections are performed through the terminal box placed in the connection box. PA supply units are supplied with the fastening brackets to facilitate mounting.	The unit can be mounted in any position but the vertical one with vertical air downstream because the electrical heating elements are not allowed under the fan. Access for the unit maintenance and filter cleaning shall be provided. The PA...W unit design enables to lead the water heater pipes to the right or to the left while mounting. The pipes are directed on the right on supply air side by default.
CONTROL AND AUTOMATION
Integrated control and automation system for speed (air flow) control and setting supply air temperature.	The unit may be remotely controlled from the external control panel fixed on wire.
CONTROL AND PROTECTION FUNCTIONS
Control from the control panel: switching the unit on/off, fan speed selection (low/medium/high speed), selecting heating/cooling modes (if connected to duct cooler). Maintaining supply air temperature set from the control panel by controlling the circulation pump and actuating the heat medium regulating valve; input from the heat medium flow switch (pump alarm). Safe start-up/ shutdown of the fans, warming up of the water heater before start-up; return heat medium temperature control when the fan is off.	Freezing protection of the water heating coils by the exhaust temperature sensor and the return heat medium temperature sensor. Control of the compressor and condensing unit of the water cooler by the room temperature sensor (for the models equipped with a duct air cooler). Filter clogging degree with differential pressure sensor. Actuating the external air damper with a return spring. Unit shut down at signal from the fire alarm system.
SUPPLEMENTARY EQUIPMENT
The mixing units USWK are recommended for smooth supply air temperature regulation in the units equipped with water heaters. The mixing unit USWK with three-way heat medium regulating valve and circulation pump provides smooth heating capacity regulation and minimizes the water heater freezing danger. To disable uncontrollable air flow when the fan is off it is recommended to install the air damper with servo actuator from outside at the unit inlet.	To protect the water heater against cold intake air in case of power failure for the units with water heaters (PA...W) it is recommended to install the air damper with a return spring. For attenuation of sound generated by the fan it is recommended to install the duct silencer (refer SR). For vibration absorbing it is recommended to install the flexible anti-vibration connectors (refer VVG) on both sides of the unit.

Characteristics

Parameter	PA 02 W4	Measurement unit
Frequency	50	Hz
Phase	3	˜
Voltage	400	V
Fan current	1.05	A
Maximum fan power	620	W
Air capacity	2350	m³/h
Total unit power	620	W
Total unit current	1.05	A
RPM	2690	min^-1
Filter	G4 (F7) pocket type*	-
Transported air temperature	-25 ... +40	°С
Sound pressure level at 3 m distance	54	dBА
Casing material	aluzinc	-
Heating	water heating	-
Insulation	50 mm mineral wool	-
Connected air duct size	500х300	mm
Number of water (glycol) coil rows	4	-
Width	500	mm
Weight	63	kg
Height	300	mm
Duct	for rectangular air ducts	-
*	option	-

Capacity diagram

Selection method:
Air flow:
Pressure:

Operating point

Air flow: --
Pressure: ---

Files archieve

Downloads

Dimensions

Characteristics

Parameter	Value	Measurement unit
B	500	mm
B1	520	mm
B2	689	mm
B3	646	mm
H	300	mm
H1	320	mm
H2	447	mm
L	1250	mm
L1	1212	mm

Additional characteristics

Sound-power level		Gen	Octave-frequency band [Hz]
Sound-power level		Gen	63	125	250	500	1000	2000	4000	8000
L_WA to inlet	dBA	69	52	69	65	60	58	49	55	49
L_WA to outlet	dBA	85	57	71	82	77	75	74	73	69
L_WA to environment	dBA	55	37	58	61	53	51	52	55	52

Hot water coil parameters

How to use water heater diagrams

System Parameters: Air flow = 2000 m³/h. Outside air temperature = -15 °C. Water temperature (in/out) = 70/50 °C.

Air Speed. Starting from 2000 m³/h on the air flow scale draw a vertical line ① till the air speed axis which makes about 3.75 m/s.
Supply air temperature. Prolong the line ① up to the point where it crosses the outside air temperature (blue curve, e.g. -15 °C); then draw a horizontal line ② from this point to the left till crossing water in/out temperature curve (e.g. 70/50 °C). From this point draw a vertical line ③ to the supply air temperature axis on top of the graphic (+31 °C).
Heating coil capacity. Prolong the line ① up to the point where it crosses the outside air temperature (e.g. -15 °C, red curve) and draw a horizontal line ④ from this point to the right until it crosses water in/out temperature curve (e.g. 70/50 °C), from here draw a vertical line ⑤ up to the scale representing the heating coil capacity (35.0 kW).
Water flow. Prolong the line ⑤ down to water flow axis at the bottom of the graphic ⑥ (0.43 l/s).
Water pressure drop. Draw the line ⑦ from the point where the line ⑥ crosses the black curve to the pressure drop axis (9.0 kPa).

Designation key

Series	Unit standard size	Heater type	Row number of the heater	Integrated control system
VENTS PA	01; 02; 03; 04	W: water	2: two rows; 3: three rows; 4: four rows	LCD: integrated automation with A13 control panel

Accessories

Type	G4 replaceable filter	F7 replaceable filter	Filter type
PA 01 W2	SFK 474x269x27 G4	SFK 474x269x27 F7	pocket filter
PA 01 W4
PA 02 W2	SFK 538x342x27 G4	SFK 538x342x27 F7	pocket filter
PA 02 W4
PA 03 W2	SFK 637x395x27 G4	SFK 637x395x27 F7	pocket filter
PA 03 W4
PA 04 W2	SFK 737x441x27 G4	SFK 737x441x27 F7	pocket filter
PA 04 W3